Recently, the Russian President hosted a meeting with oil and gas industry representatives. He said that the refusal of some Western countries to cooperate normally with Russia and deny some Russian energy resources has hit millions of European people deeply and caused an energy crisis. These "unfriendly countries" are experiencing severe inflation, and Russia is also facing the three major challenges of increasing domestic consumption of energy Concrete Foaming Generator are still very uncertain.
Description of TR30 foam generator
Foam Concrete Machine is the core equipment of foam concrete production, which has a significant impact on the quality of foam concrete. An excellent foam generator for concrete not only has a high foam output but more importantly, the quality of the foam produced is outstanding. TR30 foam generator developed by our company. It can be used in laboratories, small-scale foam concrete cast-in-situ projects, and pilot lines of foam concrete products. The outstanding advantages of TR30 foam generator are low foam moisture content, more foaming agent, high foam uniformity, large foam output, and other benefits.
Parameters of TR30 foam generator
Model | TR30 |
Maximum foam output(m3/h) | 8 |
Motor voltage(V) | 220 |
Work rate(W) | 1500 |
Pump suction(m) | 1-3 |
Dimensions(cm) | 120*50*90 |
Weight(kg) | 120 |
Usually need to be disassembled:
1. After working for a long time, it is found that the foam shape is not good, usually more than three months.
2. Pipe blockage: Some foaming agent remaining in the bubble tube will form a solid residue. In this case, the foam cannot be produced normally, or the pipeline pressure increases sharply. At this time, all the old steel balls need to be taken out, and then replaced with a new one The ball is fine. Steel wire ball specification requirements: each blowing tube needs to be filled with about 12-15 steel wire balls. Too much or too little will affect or even destroy the foam performance.
Precautions:
1. Remember to use electricity safely. If water or foam touches the circuit, you must immediately cut off the power at the remote end to ensure safe production.
2. There will be air in the pipeline when it is used for the first time. The foaming liquid has not been pumped into the equipment in a short time. You can wait for tens of seconds until the liquid is filled with the entire suction tube and the foaming operation can be performed normally.
3. Do not start the equipment when the pipeline is blocked to prevent damage to the components due to overpressure in the pipeline.
If you are looking for foam generator please feel free to contact us and send an inquiry, email address: sales@cabr-concrete.com
Recently, the first press conference of the Boao Forum For Asia Annual Conference 2022 was held. Two flagship reports were released at the conference: "Asia's Economic Prospects and Integration Process 2022" and "Sustainable Asia and the World 2022-Green Transformation in Action in Asia".
The flagship report points out that the global economy will recover in 2021, and the pace of economic integration in the Asia-Pacific has not stopped even in the face of the impact of COVID-19. The Asia-Pacific region has provided new impetus for the world's economic recovery and institutional building.
The report gives an outlook on the Asian economy, noting that a number of factors will affect Asian economic growth. For example, mutated strains such as Delta and Omicron have become more transmissible, and many economies are experiencing epidemic peaks again. The Ukraine crisis has triggered geopolitical changes in Asia and Europe, leading to higher commodity prices, which may affect the global energy supply and energy transformation.
The report pointed out that the Asian economy will still be in the process of recovery in 2022, but the growth rate may moderate. According to the report, Asia's economic growth in 2022 is likely to be lower than the current IMF forecast, which is projected at 4.8%.
Affected by several factors, the supply of the Concrete Foaming Generator is erratic and thus its prices are expected to go higher in the future.
Inquiry us
Titanium Nitride, or TiN, is a hard ceramic material that resists wear and has good thermal and electrical conductivity. It is widely used for coatings due to its unique qualities. The following are the most common applications for Titanium Nitride.…
Zinc stearate is primarily used as lube and release representative of styrene resin, phenolic resin as well as amino material, as well as vulcanizing energetic representative and conditioner in rubber.What is Zinc stearate used for?It can be utilized…
What is Titanium carbide?Titanium carbide chemical formula is TiC. The molecular weight of titanium carbide is 59.89. Gray metal face-centered cubic latticework strong. Titanium carbide melting point is 3140 & plusmn; 90 ℃. Titanium carbide boiling p…